What are the Flow Test Results for your Dump Valves

All of our Dump Valves have undergone a series of flow tests to determine the exact GPM each valve will deliver.  The test results for our valves are as follows:

 

  1. Our 1050 style Dump Valves, when tested, took 42 seconds to empty 2,500 gallons of water from a 4200 gallon tanker. Giving the 1050 style valve a flow rate of 3570 GPM (gallons per minute).
  2. Our 1010 style Dump Valves, when tested, took 51 seconds to empty 2,500 gallons of water from a 4200 gallon tanker. Giving the 1010 style valve a flow rate of 2,940 GPM.
  3. Our 1050 style dump valve in conjunction with a 6012SW & 4036-8x12, took 64 seconds to empty 2,500 gallons of water from a 4200 gallon tanker. Giving them a flow rate of 2,340 GPM.
  4. Our 7010 round Dump Valve took 64 seconds to empty 2,500 gallons of water from a 4200 gallon tanker. Giving the 7010 a flow rate of 2,340 GPM.


Please note: The following conditions can and will affect flow rates of your tank:

  1. Proper Ventilation
  2. Head Pressure
  3. Baffling inside the tank
  4. Tank configuration and size.

 

All of these flow tests where recorded and are available for viewing on our video page.

What is the difference between a square flange and an angle flange valve?

The angled flange has a two-degree angle on the flange enabling the valve to hang down slightly to improve dumping and drainage (see below), while a squared flange allows the valve to sit perpendicular to the tank.

 

 

If my tank is slightly curved how does the valve mount?

We offer a mating installation tube, our part number 105090 to weld into your tank.  This mating tube is available in mild steel, stainless steel or aluminum construction. Our valve then bolts on to the flange of the installation tube.

 

Is there a manual override for electric and air valves?

Yes there is.

For top controlled Valves simply pull the 2 snap pins to remove the electric actuator or air cylinder and replace handle; the destaco clamp is now locking the Valve shut.

The side controlled Valve also has a manual override.  To release or remove the automation, pull safety override pin and manually push valve handle to open.

I have an old valve and want to upgrade to either stainless or new style 1050 series valve, will the valve fit into my opening?

Yes, our bolt pattern has never changed on our valves.

What is the overall length of the valve with a telescoping chute?

The length on a standard 24” valve is a total of 56” when #4036 is fully extended from where the valve mounts to the tank. As a rule of thumb, if we cut off 1” on the valve length you will lose 2” additional off the length of the telescoping chute, 20” valves with #4036-54 would be 44” when extended, and 16” valve with a #4036-54 would extend 32” from tank.

I have a compartment; do you build special length valves?

Yes, we can move the controls further away from the tank and build the valve to customer specifications.  Call for length restrictions & specification order sheet – state if ordering for a top or side controlled Valve.

I have a side control valve and it is hard to hold open, what can I do?

We offer two (2) options to make holding the valve open easier. Our Part #105070, is a lock open device.  The 105070 is designed to hold the valve open when in the fully open position. We also offer, our part #106016-1, which is a telescoping handle.  This device offers better leverage in opening or closing the dump valves. Both of these items can be purchased as original equipment or added to an existing Newton Kwik Dump Valve.

 

What can I do if my valve leaks?

The first thing to check for is any rust or debris in your tank, not allowing the neoprene to seal up against the rim of the valve. Check if your neoprene is cut or damaged. Check if your bearing is damaged. Always lock the valve shut when your tanker is empty. Failure to do this will result in damage to the bearing. Do not allow the valve to slam shut, as this can also cause damage to the neoprene.

What can I do if my 1010 style valve leaks?

After checking as suggested above - the bearing is slotted and can be raised or lowered to increase tension on the neoprene seal. Also you can give the piston a half turn. If you still have leakage call for technical assistance.

What can I do if my 1050 style valve leaks?

After checking as suggested above - the bearing is slotted and can be moved to the left or right to increase tension on the neoprene seal. Tighten or loosen ¼-20 nylon locknuts, do not over tighten and bend plates. The brass is slotted and must slide freely. If you still have leakage call for technical assistance.

 

I have a valve that is already mounted, how do i know if it is a plunger or gate style valve?

Note the location of the brass shaft and bearing assembly.

 

 

For over 65 years, A.H. Stock Manufacturing Corp. has been a builder and fabricator of metal products for a variety of industries. We manufacture various components for several OEM manufacturers throughout the United States that are involved in heavy lifting equipment, large tooling centers and fabricating equipment among others. Our mission is to provide our customers with a single source for their metal fabrication needs - from raw materials to finished assemblies - that meet or exceed their expectations.

A.H. Stock Manufacturing Corp. | 8402 Center Road Newton, WI 53063 | Phone: (920) 726-4211 | Fax: (920) 726-4214 | Email:sales@ahstockmfg.com

Website Design by Strategic Strategies Inc.